Fatigue and Tensile Characteristics for Composite Materials Used in Prosthetic Socket

Main Article Content

Zuhair Salim Khamees
https://orcid.org/0009-0007-1722-8940
Asmaa Shawqy Khalil

Abstract

In this research, the use of natural materials like wool and cannabis as intermediate reinforcement for prosthetic limbs due to their comfort, affordability, and local availability was discussed. As part of this study on below-the-knee (BK) prosthetic sockets, two sets of samples were made using a vacuum method. These sets were made of natural fiber-reinforced polymer composites with lamination 80:20: group (Y) had 4 perlon, 1 wool 4 perlon, and group (G) had 4 perlon, 1 cannabis 4 perlon. The two groups were compared with a socket made of polypropylene. Tensile testing was used to determine the mechanical characteristics of the socket materials. The Y group has a yield stress of 17 MPs, an ultimate strength of 18.75 MPa, and an elastic modulus of 4.021 GPa, while for the G group, these values are 12.75 MPa, 18.84 MPa, and 4.076 GPa, respectively. The fatigue test was used to evaluate the failure characteristics of the socket. An F-socket was utilized to test the interface compression between both the limb and the socket. For the Tekscan sensor, the calculated pressure in the medial region is 350 K Pa, while it is 330 KPa in the posterior region. Solid Works software was used to draw a prosthetic socket for the numerical study. The failure safety agent for the composite material for group Y was 1.26. The finite element method (ANSYS Workbench 14.5) was used to look at the fatigue characteristics to detect the maximum stress, safety factor, and total deformation.

Article Details

Section

Articles

How to Cite

1.
Salim Khamees Z, Khalil AS. Fatigue and Tensile Characteristics for Composite Materials Used in Prosthetic Socket. IJP [Internet]. 2023 Dec. 1 [cited 2024 Dec. 27];21(4):32-44. Available from: https://ijp.uobaghdad.edu.iq/index.php/physics/article/view/1142

References

A. Takhakh, Int. J. Mech. Mechatron. Eng. 18, 62 (2018).

M. Ahmed, M. Abd-Alrahman, M. Abdallah, and M. Zarog, Int. J. Mech. Ind. Tech. 6, 18 (2018).

J. S. Chiad and M. S. a.-D. Tahir, Al-Nahrain J. Eng. Sci. 20, 832 (2017).

A. M. Takhakh, S. M. Abbas, and A. K. Ahmed, in IOP Conference Series: Materials Science and Engineering (IOP Publishing, 2018). p. 012045.

J. C. H. Goh, P. V. S. Lee, and S. Y. Chong, J. Rehab. Res. Develop. 41, 491 (2004).

M. J. Jweeg, A. Alhumandy, and H. Hamzah, Int. J. Mech. Mechatron. Eng. 17, 100 (2017).

A. N. Kareem and M. H. Faidh-Allah, J. Mech. Eng. Res. Develop. 44, 329 (2021).

A. S. Abbas and S. D. Dawood, ARPN J. Eng. Appl. Sci. 13, 5633 (2018).

H. Wang, H. Memon, E. Am Hassan, M. S. Miah, and M. A. Ali, Materials 12, 1226 (2019).

A. Caggiano, Materials 11, 442 (2018).

M. Bazli, H. Ashrafi, A. Jafari, X.-L. Zhao, H. Gholipour, and A. V. Oskouei, Comp. Part B: Eng. 157, 76 (2019).

Y.-J. Hu, C. Jiang, W. Liu, Q.-Q. Yu, and Y.-L. Zhou, Sensors 18, 3361 (2018).

G. Li, J. Zhao, and Z. Wang, Materials 11, 1028 (2018).

N. K. Faheed, J. K. Oleiwi, and Q. A. Hamad, Eng. Tech. J. 39, 1715 (2021).

A. I. Campbell, S. Sexton, C. J. Schaschke, H. Kinsman, B. Mclaughlin, and M. Boyle, Prosthet. Orthot. Int. 36, 181 (2012).

B. K. Ibrahim and F. H. Antar, Iraqi J. Sci. 59, 1587 (2018).

A. S. Khaleel, Iraqi J. Sci. 63, 1971 (2022).

S. I. Hussein, N. A. Ali, G. M. Saleh, and H. I. Jaffar, Iraqi J. Sci. 60, 1 (2019).

H. Jaffer, Iraqi J. Phys. 10, 98 (2012).

M. Nurhanisah, N. Saba, M. Jawaid, and M. Paridah, Green Biocomposites Design and Applications (Serdang, Selangor, Malaysia, Springer, 2017), p.127.

S. M. Abbas, K. K. Resan, A. K. Muhammad, and M. Al-Waily, Int. J. Mech. Eng. Tech. 9, 383 (2018).

D. Widhata and R. Ismail, in IOP conference series: materials science and engineering (IOP Publishing, 2019). p. 012127.

A. M. Takhakh, Int. J. Mech. Mechatron. Eng. 18, 62 (2018).

M. A. Al-Shammari, E. Q. Hussein, and A. A. Oleiwi, Int. J. Mech. Mechatron. Eng. 17, 57 (2017).

M. Nurhanisah, F. Hashemi, M. Paridah, M. Jawaid, and J. Naveen, in IOP Conference Series: Materials Science and Engineering (IOP Publishing, 2018). p. 012050.

M. Ahmed, M. Abd-Alrahman, M. Abdallah, and M. Zarog, Int. J. Mech. Indus. Tech. 6, 18 (2018).

H. A. Hamzah, MSc Thesis, University of Kerbala, 2018.

A. Harmaen, M. Paridah, M. Jawaid, A. Fariz, and B. Asmawi, Kenaf Fibers and Composites (Boka, Raton, CRC Press, 2018).

M. J. Jweeg, A. A. Ahumdany, and A. F. M. Jawad, Int. J. Mech. Mechatron. Eng. 19, 108 (2019).

S. M. Abbas and M. H. Abbas, Analysis and manufacturing of above knee prosthesis socket by using revo fit solution, IOP Conference Series: Materials Science and Engineering. 2018, IOP Publishing. pp. 012025.

Y. Y. Kahtan, Int. J. Mech. Eng. Tech. 10, 2127 (2019).

S. M. Abbas, in Defect and Diffusion Forum (Trans Tech Publ, 2020). p. 76.

M. R. Ismail, Y. Y. Kahtan, and S. M. Abbas, in IOP Conference Series: Materials Science and Engineering (IOP Publishing, 2020). p. 012061.

H. Z. Abdalikhwa, M. A. Al-Shammari, and E. Q. Hussein, in IOP Conference Series: Materials Science and Engineering (IOP Publishing, 2021). p. 012170.

Z. S. Khamees and A. S. Khaleel, Bio. Gecko. 12, 1730 (2023).

M. Mohamed, N. Fahad, M. Al-Waily, and K. Resan, Int. J. Mech. Eng. Tech. 09, 729 (2018).

M. Al-Waily, A. Kadhim, Z. Alhilo, M. Jweeg, and K. Resan, Int. J. Mech. Mechatron. Eng. 18, 77 (2018).

K. Resan, I. Al-Razaq, and Y. Ibrahim, J. Eng. Develop. 20, 147 (2016).

S. S. Hassan, K. K. Resan, and A. Z. Mahdi, Eng. Tech. J. 31, 1521 (2013).

A. S. Hammood, M. Al-Waily, and A. Abd. Kamaz, Iraqi J. Mech. Mat. Eng. 11, 344 (2011).

D. Al-Zubaidi and M. Al-Shammari, Mat. Sci. Forum 7, 4667 (2022).

M. J. J. Muhsin, Iraqi J. Mech. Mat. Eng. 13, 689 (2013).

Z. A. Ali, A. A. Kadhim, R. H. Al-Khayat, and M. Al-Waily, J. Mech. Eng. Res. Develop. 44, 392 (2021).

M. Al-Waily and A. S. Humod, Iraqi J. Mech. Mat. Eng. 10, 58 (2010).

A. A. Kadhim, E. A. Abbod, A. K. Muhammad, K. K. Resan, and M. Al-Waily, J. Mech. Eng. Res. Develop. 44, 383 (2021).

M. L. Al-Waily, MSc Thesis, Kufa University, (2004).

E. K. Njim, S. H. Bakhy, and M. Al-Waily, J. Appl. Sci. Eng. 25, 339 (2021).

F. Mohanad, A. Takhakh, and A. Abdullah, J. Mech. Eng. Res. Develop. 42, 118 (2019).

F. M. Kadhim, J. S. Chiad, and A. M. Takhakh, in IOP Conference Series: Materials Science and Engineering (IOP Publishing, 2018). p. 012078.

B. A. Miller, R. J. Shipley, R. J. Parrington, and D. P. Dennies, ASM International Handbook (USA, ASM International, 2002).

Similar Articles

You may also start an advanced similarity search for this article.